81 FR 24 - Airworthiness Directives; The Boeing Company Airplanes
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration Federal Register Volume 81, Issue 1 (January 4, 2016)
Federal Aviation Administration
Federal Register Volume 81, Issue 1 (January 4, 2016)
| Page Range | 24-27 | |
| FR Document | 2015-32903 |
[Federal Register Volume 81, Number 1 (Monday, January 4, 2016)] [Proposed Rules] [Pages 24-27] From the Federal Register Online [www.thefederalregister.org] [FR Doc No: 2015-32903] ----------------------------------------------------------------------- DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA-2015-8135; Directorate Identifier 2015-NM-106-AD] RIN 2120-AA64 Airworthiness Directives; The Boeing Company Airplanes AGENCY: Federal Aviation Administration (FAA), DOT. [[Page 25]] ACTION: Notice of proposed rulemaking (NPRM). ----------------------------------------------------------------------- SUMMARY: We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, and -400ER series airplanes. This proposed AD was prompted by multiple reports of un- commanded escape slide inflation. This proposed AD would require modifying the regulator valves of the forward entry door, forward service door, aft entry door, and aft service door, and as applicable, modifying the regulator valves of the mid entry door and mid service door. We are proposing this AD to prevent out-of-tolerance trigger mechanism components (sector and sear) in the regulator valves, which can produce insufficient trigger engagement and reduced pull force values, possibly leading to un-commanded deployment of the slide during normal airplane maintenance or operation, and could result in injury to passengers and crew, damage to equipment, and the slide becoming unusable in an emergency evacuation. DATES: We must receive comments on this proposed AD by February 18, 2016. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments. Fax: 202-493-2251. Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590. Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544- 5000, extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA 98057-3356. For information on the availability of this material at the FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-8135. Examining the AD Docket You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2015- 8135; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Kimberly DeVoe, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6495; fax: 425-917- 6590; email: [email protected]. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2015-8135; Directorate Identifier 2015-NM-106-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion We received reports of two incidents of un-commanded escape slide inflation. In both cases, out-of-tolerance trigger mechanism components (sector and sear) were found in the regulator valves which produced insufficient trigger engagement and reduced pull force values. This condition, if not corrected, could result in possible un-commanded deployment of the slide during normal airplane maintenance or operation and could result in injury to passengers and crew, damage to equipment, and the slide becoming unusable in an emergency evacuation. Related Service Information Under 1 CFR Part 51 We reviewed Boeing Service Bulletin 767-25-0548, Revision 1, dated April 23, 2015. The service information describes procedures for modifying the regulator valves of the forward entry door, forward service door, aft entry door, aft service door, mid entry door and mid service door. The modification includes replacing the existing trigger mechanism sector and sear of the regulator valve with new trigger mechanism sector and sear. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section of this NPRM. FAA's Determination We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements This proposed AD would require accomplishing the actions specified in the service information identified previously. For information on the procedures and compliance times, see this service information at http://www.regulations.gov by searching for and locating Docket No. FAA-2015-8135. Explanation of ``RC'' Steps in Service Information The FAA worked in conjunction with industry, under the Airworthiness Directive Implementation Aviation Rulemaking Committee (ARC), to enhance the AD system. One enhancement was a new process for annotating which steps in the service information are required for compliance with an AD. Differentiating these steps from other tasks in the service information is expected to improve an owner's/operator's understanding of crucial AD requirements and help provide consistent judgment in AD compliance. The steps identified as Required for Compliance (RC) in any service information identified previously have a direct effect on detecting, preventing, resolving, or eliminating an identified unsafe condition. For service information that contains steps that are labeled as RC, the following provisions apply: (1) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD, and an AMOC [[Page 26]] is required for any deviations to RC steps, including substeps and identified figures; and (2) steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. Costs of Compliance We estimate that this proposed AD affects 302 airplanes of U.S. registry. We estimate the following costs to comply with this proposed AD: Estimated Costs ---------------------------------------------------------------------------------------------------------------- Cost per Cost on U.S. Action Labor cost Parts cost product operators ---------------------------------------------------------------------------------------------------------------- Replacement of trigger mechanism 15 work-hours x $85 per $2,236 $3,511 $1,060,322 components--forward and aft entry/ hour = $1,275. service doors. Replacement of trigger mechanism 8 work-hours x $85 per 1,118 1,798 542,996 components--mid entry/service doors. hour = $680. ---------------------------------------------------------------------------------------------------------------- Authority for This Rulemaking Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ``General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: (1) Is not a ``significant regulatory action'' under Executive Order 12866, (2) Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD): The Boeing Company: Docket No. FAA-2015-8135; Directorate Identifier 2015-NM-106-AD. (a) Comments Due Date We must receive comments by February 18, 2016. (b) Affected ADs None. (c) Applicability This AD applies to The Boeing Company Model 767-200, -300, and - 400ER series airplanes, certificated in any category, as identified in Boeing Service Bulletin 767-25-0548, Revision 1, dated April 23, 2015. (d) Subject Air Transport Association (ATA) of America Code 25, Equipment/ furnishings. (e) Unsafe Condition This AD was prompted by multiple reports of un-commanded escape slide inflation. We are issuing this AD to prevent out-of-tolerance trigger mechanism components (sector and sear) in the regulator valves, which can produce insufficient trigger engagement and reduced pull force values, possibly leading to un-commanded deployment of the slide during normal airplane maintenance or operation, and could result in injury to passengers and crew, damage to equipment, and the slide becoming unusable in an emergency evacuation. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Replacement of the Trigger Mechanism Sector and Sear Within 42 months after the effective date of this AD, modify the regulator valves of the forward entry door, forward service door, aft entry door, and aft service door, and as applicable, modify the regulator valves of the mid entry door and mid service door, in accordance with the Accomplishment Instructions of Boeing Service Bulletin 767-25-0548, Revision 1, dated April 23, 2015. (h) Credit for Previous Actions This paragraph provides credit for the modification required by paragraph (g) of this AD, if the modification was performed before the effective date of this AD using Boeing Service Bulletin 767-25- 0548, dated November 5, 2014, which is not incorporated by reference in this AD. (i) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (j)(1) of this AD. Information may be emailed to: [email protected]. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. For a repair [[Page 27]] method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (4) For service information that contains steps that are labeled as Required for Compliance (RC), the provisions of paragraphs (i)(4)(i) and (i)(4)(ii) apply. (i) The steps labeled as RC, including substeps under an RC step and any figures identified in an RC step, must be done to comply with the AD. An AMOC is required for any deviations to RC steps, including substeps and identified figures. (ii) Steps not labeled as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the RC steps, including substeps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. (j) Related Information (1) For more information about this AD, contact Kimberly DeVoe, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6495; fax: 425-917-6590; email: [email protected]. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone: 206-544- 5000, extension 1; fax: 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information at the FAA Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA 98057-3356. For information on the availability of this material at the FAA, call 425-227-1221. Issued in Renton, WA, on December 21, 2015. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2015-32903 Filed 12-31-15; 8:45 am] BILLING CODE 4910-13-P
Document Created: 2015-12-31 23:04:53
Document Modified: 2015-12-31 23:04:53
| Category | Regulatory Information | |
| Collection | Federal Register | |
| sudoc Class | AE 2.7: GS 4.107: AE 2.106: | |
| Publisher | Office of the Federal Register, National Archives and Records Administration | |
| Section | Proposed Rules | |
| Action | Notice of proposed rulemaking (NPRM). | |
| Dates | We must receive comments on this proposed AD by February 18, 2016. | |
| Contact | Kimberly DeVoe, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; phone: 425-917-6495; fax: 425-917- 6590; email: [email protected] | |
| FR Citation | 81 FR 24 | |
| RIN Number | 2120-AA64 | |
| CFR Associated | Air Transportation; Aircraft; Aviation Safety; Incorporation by Reference and Safety |
2025 Federal Register | Disclaimer | Privacy Policy
USC | CFR | eCFR