The FAA proposes to supersede Airworthiness Directive (AD) 2024-14-09, which applies to certain Dassault Aviation Model FALCON 7X, FALCON 900EX, and FALCON 2000EX airplanes. AD ...
The FAA proposes to supersede Airworthiness Directive (AD) 2024-14-09, which applies to certain Dassault Aviation Model FALCON 7X, FALCON 900EX, and FALCON 2000EX airplanes. AD 2024-14-09 requires replacement of certain titanium screws, adds other locations for screw replacement, and revises the applicability from AD 2022-02-10. Since the FAA issued AD 2024-14-09, affected parts have been found in other areas of certain FALCON 7X airplanes as well as in additional FALCON 7X airplanes. This proposed AD would continue to require the actions in AD 2024-14-09 and would require expanding the applicability to additional airplanes, expanding the locations for screw replacement, and revising the compliance times for parts replacement. This AD would also limit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.
DATES:
The FAA must receive comments on this proposed AD by January 4, 2027.
ADDRESSES:
You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal:
Go to
regulations.gov. Follow the instructions for submitting comments.
Fax:
202-493-2251.
Mail:
U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
Hand Delivery:
Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket:
You may examine the AD docket at
regulations.gov
under Docket No. FAA-2026-13821; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.
Material Incorporated by Reference:
For Dassault Aviation material identified in this proposed AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; websitedassaultfalcon.com.
For European Union Aviation Safety Agency (EASA) material identified in this proposed AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; emailADs@easa.europa.eu.
You may find this material on the EASA website at
ad.easa.europa.eu.
It is also available at
regulations.gov
under Docket No. FAA-2026-13821.
You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.
FOR FURTHER INFORMATION CONTACT:
Amanda F. Pieraccini, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7329; email:
9-AVS-AIR-BACO-COS@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments using a method listed under the
ADDRESSES
section. Include “Docket No. FAA-2026-13821; Project Identifier MCAI-2025-01619-T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Amanda F. Pieraccini, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7329; email:
9-AVS-AIR-BACO-COS@faa.gov.
Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.
Background
The FAA issued AD 2024-14-09, Amendment 39-22790 (89 FR 72966, September 9, 2024) (AD 2024-14-09), for certain Dassault Aviation Model FALCON 7X, FALCON 900EX, and FALCON 2000EX airplanes. AD 2024-14-09 was prompted by MCAI originated by EASA, which is the Technical Agent for the Member States of the European Union. EASA issued EASA AD 2023-0207, dated November 21, 2023 (EASA AD 2023-0207), to correct an unsafe condition.
AD 2024-14-09 requires replacement of certain titanium screws, adds other locations for screw replacement, and revises the applicability. The FAA issued AD 2024-14-09 to address failure of an affected screw installed in a critical location, possibly resulting in reduced structural integrity of the airplane.
Actions Since AD 2024-14-09 Was Issued
Since the FAA issued AD 2024-14-09, EASA superseded EASA AD 2023-0207 and issued EASA AD 2025-0228R1, dated February 6, 2026 (EASA AD 2025-0228R1) (also referred to as the MCAI), to correct an unsafe condition for certain Dassault Aviation Model FALCON 7X, FALCON 900EX, and FALCON 2000EX airplanes. The MCAI states that since EASA issued EASA AD 2023-0207, it was determined that affected parts have been installed in additional areas of certain Model FALCON 7X airplanes already included in the applicability of EASA AD 2023-0207. The MCAI also states that it was
( printed page 74512)
determined that additional Model FALCON 7X airplanes were not included in the applicability of EASA AD 2023-0207. The MCAI further states that the compliance time for parts replacement specified in EASA AD 2023-0207 can be defined in flight cycles (FC) only; therefore, the calendar-based compliance times were removed.
The FAA is proposing this AD to address failure of an affected screw installed in a critical location, possibly resulting in reduced structural integrity of the airplane. You may examine the MCAI in the AD docket at
regulations.gov
under Docket No. FAA-2026-13821.
Explanation of Retained Requirements
Although this proposed AD does not explicitly restate the requirements of AD 2024-14-09, this proposed AD would retain all of the requirements of AD 2024-14-09. Those requirements are referenced in EASA AD 2025-0228R1, which, in turn, is referenced in paragraph (g) of this proposed AD.
Material Incorporated by Reference Under 1 CFR Part 51
EASA AD 2025-0228R1 specifies procedures for replacing certain Decomatic titanium screws, including an inspection of the bore dimension and corrective actions (oversizing or repair). EASA AD 2025-0228R1 also limits installation of certain Decomatic titanium screws.
This proposed AD would also require Dassault Service Bulletin 7X-467, Revision 2, dated March 20, 2023, which the Director of the Federal Register approved for incorporation by reference as of October 15, 2024 (89 FR 72966, September 9, 2024).
This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the
ADDRESSES
section.
FAA's Determination
These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI and material referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified in EASA AD 2025-0228R1 described previously, except for any differences identified as exceptions in the regulatory text of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2025-0228R1 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2025-0228R1 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2025-0228R1 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times”, compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2025-0228R1. Service information required by EASA AD 2025-0228R1 for compliance will be available at
regulations.gov
under Docket No. FAA-2026-13821 after the FAA final rule is published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would affect 52 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:
Estimated Costs for Required Actions
Labor cost
Parts cost
Cost per product
Cost on U.S. operators
Up to 250 work-hours × $85 per hour = $21,250
Up to $524 *
Up to $21,774
Up to $1,132,248.
* The FAA estimates that the rental of special tooling to accomplish replacement of any affected Decomatic titanium screw on Model FALCON 7X airplanes, serial number (S/N) 423 through 443 (inclusive), to be $524 per day.
According to the manufacturer, some or all of the costs of this proposed AD may be covered under warranty, thereby reducing the cost impact on affected individuals. The FAA does not control warranty coverage for affected individuals. As a result, the FAA has included all known costs in the cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
(2) Would not affect intrastate aviation in Alaska, and
( printed page 74513)
(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
The FAA must receive comments on this airworthiness directive (AD) by January 4, 2027.
(b) Affected ADs
This AD replaces AD 2024-14-09, Amendment 39-22790 (89 FR 72966, September 9, 2024) (AD 2024-14-09).
(c) Applicability
This AD applies to Dassault Aviation airplanes identified in paragraphs (c)(1) through (3) of this AD, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2025-0228R1, dated February 6, 2026 (EASA AD 2025-0228R1).
(1) Model FALCON 7X airplanes.
(2) Model FALCON 900EX airplanes.
(3) Model FALCON 2000EX airplanes.
(d) Subject
Air Transport Association (ATA) of America Code 51, Standard Practices/Structures.
(e) Unsafe Condition
This AD was prompted by a report of an improper heat treatment process applied during the manufacturing of certain Decomatic titanium screws, and by the determination that affected parts in additional areas on certain airplanes, as well as additional airplanes, are subject to the unsafe condition. The FAA is issuing this AD to address failure of an affected screw installed in a critical location, possibly resulting in reduced structural integrity of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2025-0228R1.
(h) Exceptions to EASA AD 2025-0228R1
(1) Where EASA AD 2025-0228R1 refers to October 30, 2025 (the effective date of the original issue of EASA AD 2025-0228), this AD requires using the effective date of this AD.
(2) Where the “Ref Publications” section of EASA AD 2025-0228R1 specifies “Dassault SB 7X-467 original issue dated 16 November 2020, Rev. 1 dated 12 December 2022, Rev. 2 dated 20 March 2023, Rev. 03 dated 11 March 2024, Rev. 04 dated 22 April 2024, Rev. 05 dated 09 September 2024 and Rev. 06 dated 10 April 2025 (including its Erratum dated 09 June 2025)”, this AD requires replacing that text with “Dassault Service Bulletin 7X-467, Rev. 06 dated April 10, 2025 (including its Erratum dated June 09, 2025)”.
(3) This AD does not adopt the “Remarks” section of EASA AD 2025-0228R1.
(i) Credit for Previous Actions
(1) For Model FALCON 7X airplanes: This paragraph provides credit for the actions specified in paragraph (g) of this AD, if those actions were performed before October 15, 2024 (the effective date of AD 2024-14-09) using Dassault Service Bulletin 7X-467, dated November 16, 2020, provided the additional work specified in Dassault Service Bulletin 7X-467, Revision 2, dated March 20, 2023, and the additional work specified in the applicable SB as defined in EASA AD 2025-0228R1 is accomplished within the applicable compliance time specified in EASA AD 2025-0228R1.
(2) For Model FALCON 7X airplanes: This paragraph provides credit for the actions specified in paragraph (g) of this AD, if those actions were performed before the effective date of this AD using Dassault Service Bulletin 7X-467, Revision 2, dated March 20, 2023, Dassault Service Bulletin 7X-467, Revision 3, dated March 11, 2024, Dassault Service Bulletin 7X-467, Revision 4, dated April 22, 2024, or Dassault Service Bulletin 7X-467, Revision 5, dated September 9, 2024, provided the additional work specified in the applicable SB as defined in EASA AD 2025-0228R1 is accomplished within the applicable compliance time specified in EASA AD 2025-0228R1.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1)
Alternative Methods of Compliance (AMOCs):
The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (k)(1) of this AD and email to:
AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2)
Contacting the Manufacturer:
For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(k) Additional Information
(1) Amanda F. Pieraccini, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7329; email:
9-AVS-AIR-BACO-COS@faa.gov.
(2) Material identified in this AD that is not incorporated by reference is available at the address specified in paragraph (l)(5) of this AD.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise.
(3) The following material was approved for IBR on [DATE 35 DAYS AFTER PUBLICATION OF THE FINAL RULE].
(i) European Union Aviation Safety Agency (EASA) AD 2025-0228R1, dated February 6, 2026.
(ii) [Reserved]
(4) The following material was approved for IBR on October 15, 2024 (89 FR 72966, September 9, 2024).
(i) Dassault Service Bulletin 7X-467, Revision 2, dated March 20, 2023.
(ii) [Reserved]
(5) For Dassault Aviation material identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; website
dassaultfalcon.com.
(6) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
ADs@easa.europa.eu.
You may find this material on the EASA website at
ad.easa.europa.eu.
(7) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.