Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2021-12-17, which applies to certain ATR--GIE Avions de Transport R[eacute]gional Model ATR42-300, -320, and -500 airp...
The FAA proposes to supersede Airworthiness Directive (AD) 2021-12-17, which applies to certain ATR—GIE Avions de Transport Régional Model ATR42-300, -320, and -500 airplanes; and all Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes. AD 2021-12-17 requires a detailed visual inspection of each affected part for deficiencies (sealant blockage and out of tolerance ligaments), and depending on findings, accomplishment of applicable corrective actions. Since the FAA issued AD 2021-12-17, it was determined that additional seat track part numbers and airplanes may be affected. This proposed AD would continue to require the actions in AD 2021-12-17 and would require inspections of additional parts. This proposed AD would also limit the installation of affected parts. The FAA is proposing this AD to address the unsafe condition on these products.
DATES:
The FAA must receive comments on this proposed AD by January 4, 2027.
ADDRESSES:
You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal:
Go to
regulations.gov. Follow the instructions for submitting comments.
Fax:
202-493-2251.
Mail:
U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
Hand Delivery:
Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket:
You may examine the AD docket at
regulations.gov
under Docket No. FAA-2026-13820; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.
Material Incorporated by Reference:
For European Union Aviation Safety Agency (EASA) material identified in this proposed AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; emailADs@easa.europa.eu.
You may find this material on the EASA website at
ad.easa.europa.eu.
It is also available at
regulations.gov
under Docket No. FAA-2026-13820.
You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.
FOR FURTHER INFORMATION CONTACT:
Yaser Osman, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 860-386-1786; email:
9-AVS-AIR-BACO-COS@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments using a method listed under the
ADDRESSES
section. Include “Docket No. FAA-2026-13820; Project Identifier MCAI-2025-01552-T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Yaser Osman, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 860-386-1786; email:
9-AVS-AIR-BACO-COS@faa.gov.
Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.
Background
The FAA issued AD 2021-12-17, Amendment 39-21604 (86 FR 34621, June 30, 2021) (AD 2021-12-17), for certain ATR—GIE Avions de Transport Régional Model ATR42-300, -320, and -500 airplanes; and all Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes. AD 2021-12-17 was prompted by an MCAI originated by EASA, which is the Technical Agent for the Member States of the European Union. EASA issued AD 2020-0097R1, dated May 28, 2020 (EASA AD 2020-0097R1), to correct an unsafe condition.
AD 2021-12-17 requires a detailed visual inspection of each affected part for deficiencies (sealant blockage and out of tolerance ligaments), and depending on findings, accomplishment of applicable corrective actions. The FAA issued AD 2021-12-17 to address structural failure of the seat track
( printed page 74500)
attachment during an emergency landing, possibly resulting in injury to occupants, and affecting emergency evacuation.
Actions Since AD 2021-12-17 Was Issued
Since the FAA issued AD 2021-12-17, EASA superseded EASA AD 2020-0097R1 and issued EASA AD 2025-0205R3, dated December 8, 2025 (EASA AD 2025-0205R3) (also referred to as the MCAI), to correct an unsafe condition for all ATR—GIE Avions de Transport Régional Model ATR42-200, -300, -320, -400, and -500 airplanes; and all Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes. Model ATR42-400 airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this proposed AD therefore does not include those airplanes in the applicability. The MCAI states that since EASA AD 2020-0097R1 was issued it was determined additional seat track part numbers might be affected and additional airplanes need to be inspected. EASA AD 2025-0205R3 also specifies that airplanes with certain configurations do not need to do the inspection and corrective actions.
The FAA is proposing this AD to address a structural failure of the seat track attachment during an emergency landing, possibly resulting in injury to occupants, and affecting emergency evacuation. You may examine the MCAI in the AD docket at
regulations.gov
under Docket No. FAA-2026-13820.
Explanation of Retained Requirements
Although this proposed AD does not explicitly restate the requirements of AD 2021-12-17, this proposed AD would retain all of the requirements of AD 2021-12-17. Those requirements are referenced in EASA AD 2025-0205R3, which, in turn, is referenced in paragraph (g) of this proposed AD.
Material Incorporated by Reference Under 1 CFR part 51
The FAA reviewed EASA AD 2025-0205R3, which specifies procedures for a detailed visual inspection of each affected seat track for deficiencies (sealant blockage and out of tolerance ligaments), and corrective actions if necessary. Corrective actions include replacement of seat track sections, and replacement of the entire seat track. EASA AD 2025-0205R3 specifies configurations on which the inspection and corrective actions are not required as well as conditions under which the corrective actions may be postponed. EASA AD 2025-0205R3 also limits the installation of affected parts.
This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the
ADDRESSES
section.
FAA's Determination
These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified in EASA AD 2025-0205R3 described previously, except for any differences identified as exceptions in the regulatory text of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2025-0205R3 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2025-0205R3 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2025-0205R3 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2025-0205R3. Material required by EASA AD 2025-0205R3 for compliance will be available at
regulations.gov
under Docket No. FAA-2026-13820 after the FAA final rule is published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would affect 33 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:
Estimated Costs for Required Actions
Labor cost
Parts cost
Cost per product
Cost on U.S. operators
Up to 40 work-hours × $85 per hour = $3,400
$0
$3,400
$112,200
The FAA estimates the following costs to do any necessary on-condition actions that would be required based on the results of any required actions. The FAA has no way of determining the number of aircraft that might need these on-condition actions:
Estimated Costs of On-Condition Actions
Labor cost
Parts cost
Cost per product
Up to 270 work-hours × $85 per hour = $22,950
(*)
$22,950
* The FAA has received no definitive data on which to base the cost estimates for the parts cost for the on-condition actions specified in this proposed AD.
( printed page 74501)
According to the manufacturer, some or all of the costs of this proposed AD may be covered under warranty, thereby reducing the cost impact on affected individuals. The FAA does not control warranty coverage for affected individuals. As a result, the FAA has included all known costs in the cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
a. Removing Airworthiness Directive (AD) 2021-12-17, Amendment 39-21604 ( 86 FR 34621, June 30, 2021); and
b. Adding the following new AD:
ATR—GIE Avions de Transport Régional:
Docket No. FAA-2026-13820; Project Identifier MCAI-2025-01552-T.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive (AD) by January 4, 2027.
(b) Affected ADs
This AD replaces AD 2021-12-17, Amendment 39-21604 (86 FR 34621, June 30, 2021) (AD 2021-12-17).
(c) Applicability
This AD applies to all ATR—GIE Avions de Transport Régional Model ATR42-200, -300, -320, and -500 airplanes; and all Model ATR72-101, -102, -201, -202, -211, -212, and -212A airplanes, certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code 53, Fuselage.
(e) Unsafe Condition
This AD was prompted by reports of defective seat tracks and a determination that additional airplanes and seat track part numbers are affected. The FAA is issuing this AD to address a structural failure of the seat track attachment during an emergency landing, possibly resulting in injury to occupants, and affecting emergency evacuation.
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2025-0205R3, dated December 8, 2025 (EASA AD 2025-0205R3).
(h) Exceptions to EASA AD 2025-0205R3
(1) Where EASA AD 2025-0205R3 refers to October 6, 2025 (the effective date of the original issue of EASA AD 2025-0205), this AD requires using the effective date of this AD.
(2) Where paragraph (2) EASA AD 2025-0205R3 specifies “deficiencies are found, as defined in the SB”, this AD requires replacing that text with “any sealant blockage or out of tolerance ligament is found”.
(3) This AD does not adopt the “Remarks” section of EASA AD 2025-0205R3.
(i) No Reporting Requirement
Although the material referenced in EASA AD 2025-0205R3 specifies to submit certain information to the manufacturer, this AD does not include that requirement.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1)
Alternative Methods of Compliance (AMOCs):
The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD and email to:
AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2)
Contacting the Manufacturer:
For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or ATR—GIE Avions de Transport Régional's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(k) Additional Information
For more information about this AD, contact Yaser Osman, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 860-386-1786; email:
9-AVS-AIR-BACO-COS@faa.gov.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2025-0205R3, dated December 8, 2025.
(ii) [Reserved]
(3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
ADs@easa.europa.eu.
You may find this material on the EASA website at
ad.easa.europa.eu.
(4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.