| Page Range | 75442-75444 | |
| FR Document | 2016-26203 |
[Federal Register Volume 81, Number 210 (Monday, October 31, 2016)] [Notices] [Pages 75442-75444] From the Federal Register Online [www.thefederalregister.org] [FR Doc No: 2016-26203] ----------------------------------------------------------------------- DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2007-0039] Intertek Testing Services NA, Inc.: Application for Expansion of Recognition AGENCY: Occupational Safety and Health Administration (OSHA), Labor. ACTION: Notice. ----------------------------------------------------------------------- SUMMARY: In this notice, OSHA announces the application of Intertek Testing Services NA, Inc. for expansion of its recognition as a Nationally Recognized Testing Laboratory (NRTL) and presents the Agency's preliminary finding to grant the application. DATES: Submit comments, information, and documents in response to this notice, or requests for an extension of time to make a submission, on or before November 15, 2016. ADDRESSES: Submit comments by any of the following methods: 1. Electronically: Submit comments and attachments electronically at http://www.regulations.gov, which is the Federal eRulemaking Portal. Follow the instructions online for making electronic submissions. 2. Facsimile: If submissions, including attachments, are not longer than 10 pages, commenters may fax them to the OSHA Docket Office at (202) 693-1648. 3. Regular or express mail, hand delivery, or messenger (courier) service: Submit comments, requests, and any attachments to the OSHA Docket Office, Docket No. OSHA-2007-0039, Technical Data Center, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3653, Washington, DC 20210; telephone: (202) 693-2350 (TTY number: (877) 889- 5627). Note that security procedures may result in significant delays in receiving comments and other written materials by regular mail. Contact the OSHA Docket Office for information about security procedures concerning delivery of materials by express mail, hand delivery, or messenger service. The hours of operation for the OSHA Docket Office are 8:15 a.m.-4:45 p.m., e.t. 4. Instructions: All submissions must include the Agency name and the OSHA docket number (OSHA-2007-0039). OSHA places comments and other materials, including any personal information, in the public docket without revision, and these materials will be available online at http://www.regulations.gov. Therefore, the Agency cautions commenters about submitting statements they do not want made available to the public, or submitting comments that contain personal information (either about themselves or others) such as Social Security numbers, birth dates, and medical data. 5. Docket: To read or download submissions or other material in the docket, go to http://www.regulations.gov or the OSHA Docket Office at the address above. All documents in the docket are listed in the http://www.regulations.gov index; however, some information (e.g., copyrighted material) is not publicly available to read or download through the Web site. All submissions, including copyrighted material, are available for inspection at the OSHA Docket Office. Contact the OSHA Docket Office for assistance in locating docket submissions. 6. Extension of comment period: Submit requests for an extension of the comment period on or before November 15, 2016 to the Office of Technical Programs and Coordination Activities, Directorate of Technical Support and Emergency Management, Occupational Safety and Health Administration, U.S. [[Page 75443]] Department of Labor, 200 Constitution Avenue NW., Room N-3655, Washington, DC 20210, or by fax to (202) 693-1644. FOR FURTHER INFORMATION CONTACT: Information regarding this notice is available from the following sources: Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office of Communications, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; email: [email protected]. General and technical information: Contact Mr. Kevin Robinson, Director, Office of Technical Programs and Coordination Activities, Directorate of Technical Support and Emergency Management, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3655, Washington, DC 20210; phone: (202) 693-2110 or email: [email protected]. SUPPLEMENTARY INFORMATION: I. Notice of the Application for Expansion The Occupational Safety and Health Administration is providing notice that Intertek Testing Services NA, Inc. (ITSNA), is applying for expansion of its current recognition as an NRTL. ITSNA requests the addition of twenty-three (23) test standards to its NRTL scope of recognition. OSHA recognition of an NRTL signifies that the organization meets the requirements specified in 29 CFR 1910.7. Recognition is an acknowledgment that the organization can perform independent safety testing and certification of the specific products covered within its scope of recognition. Each NRTL's scope of recognition includes (1) the type of products the NRTL may test, with each type specified by its applicable test standard; and (2) the recognized site(s) that has/have the technical capability to perform the product-testing and product- certification activities for test standards within the NRTL's scope. Recognition is not a delegation or grant of government authority; however, recognition enables employers to use products approved by the NRTL to meet OSHA standards that require product testing and certification. The Agency processes applications by an NRTL for initial recognition and for an expansion or renewal of this recognition, following requirements in Appendix A to 29 CFR 1910.7. This appendix requires that the Agency publish two notices in the Federal Register in processing an application. In the first notice, OSHA announces the application and provides its preliminary finding. In the second notice, the Agency provides its final decision on the application. These notices set forth the NRTL's scope of recognition or modifications of that scope. OSHA maintains an informational Web page for each NRTL, including ITSNA, which details the NRTL's scope of recognition. These pages are available from the OSHA Web site at http://www.osha.gov/dts/otpca/nrtl/index.html. ITSNA currently has fourteen (14) facilities (sites) recognized by OSHA for product testing and certification, with its headquarters located at: Intertek Testing Services NA, Inc., 545 East Algonquin Road, Suite F, Arlington Heights, Illinois 60005. A complete list of ITSNA's scope of recognition is available at https://www.osha.gov/dts/otpca/nrtl/its.html. II. General Background on the Application ITSNA submitted an application, dated April 21, 2015 (OSHA-2007- 0039-0022), to expand its recognition to include twenty-three (23) additional test standards. OSHA staff performed detailed analysis of the application packet and reviewed other pertinent information. OSHA did not perform any on-site reviews in relation to this application. Table 1 below lists the appropriate test standards found in ITSNA's application for expansion for testing and certification of products under the NRTL Program. Table 1--Proposed List of Appropriate Test Standards for Inclusion in ITSNA's NRTL Scope of Recognition ------------------------------------------------------------------------ Test standard Test standard title ------------------------------------------------------------------------ UL 5C............................. Standard for Surface Raceways and Fittings for Use with Data, Signal and Control Circuits. UL 50E............................ Enclosures for Electrical Equipment, Environmental Considerations. UL 565............................ Standard for Liquid-Level Gauges for Anhydrous Ammonia and LP-Gas. UL 60745-2-1...................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-1: Particular Requirements for Drills and Impact Drills. UL 60745-2-14..................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-14: Particular Requirements for Planers. UL 60745-2-17..................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-17: Particular Requirements for Routers and Trimmers. UL 60745-2-3...................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-3: Particular Requirements for Grinders, Polishers and Disk-Type Sanders. UL 962A........................... Standard for Furniture Power Distribution Units. UL 1769........................... Standard for Cylinder Valves. UL 2061........................... Standard for Adapters and Cylinder Connection Devices for Portable LP- Gas Cylinder Assemblies. UL 2108........................... Standard for Low-Voltage Lighting Systems. UL 2238........................... Standard for Cable Assemblies and Fittings for Industrial Control and Signal Distribution. UL 2305........................... Standard for Display Units, Fabrication and Installation. UL 2438........................... Standard for Outdoor Seasonal-Use Cord-Connected Wiring Devices. UL 5085-2......................... Low Voltage Transformers--Part 2: General Purpose Transformers. UL 61010-031...................... Safety-Requirements for Electrical Equipment for Measurement, Control and Laboratory Use--Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test. UL 61010-2-030.................... Safety requirements for electrical equipment for measurement, control and laboratory use--Part 2-030: Particular requirements for testing and measuring circuits. UL 60730-2-2...................... Standard for Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Thermal Motor Protectors. UL 60745-2-5...................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-5: Particular Requirements for Circular Saws. UL 60745-2-21..................... Hand-Held Motor-Operated Electric Tools--Safety--Part 2-21: Particular Requirements for Drain Cleaners. UL 60950-23....................... Information Technology Equipment-- Safety--Part 23: Large Data Storage Equipment. UL 62368-1........................ Audio/video, information and communication technology equipment-- Part 1: Safety requirements. [[Page 75444]] UL 1691........................... Single Pole Locking-Type Separable Connectors. ------------------------------------------------------------------------ III. Preliminary Findings on the Application ITSNA submitted an acceptable application for expansion of its scope of recognition. OSHA's review of the application file, and pertinent documentation, indicate that ITSNA can meet the requirements prescribed by 29 CFR 1910.7 for expanding its recognition to include the addition of these twenty-three test standards for NRTL testing and certification listed above. This preliminary finding does not constitute an interim or temporary approval of ITSNA's application. OSHA welcomes public comment as to whether ITSNA meets the requirements of 29 CFR 1910.7 for expansion of its recognition as an NRTL. Comments should consist of pertinent written documents and exhibits. Commenters needing more time to comment must submit a request in writing, stating the reasons for the request. Commenters must submit the written request for an extension by the due date for comments. OSHA will limit any extension to 10 days unless the requester justifies a longer period. OSHA may deny a request for an extension if the request is not adequately justified. To obtain or review copies of the exhibits identified in this notice, as well as comments submitted to the docket, contact the Docket Office, Room N-3653, Occupational Safety and Health Administration, U.S. Department of Labor, at the above address. These materials also are available online at http://www.regulations.gov under Docket No. OSHA-2007-0039 OSHA staff will review all comments to the docket submitted in a timely manner and, after addressing the issues raised by these comments, will recommend to the Assistant Secretary for Occupational Safety and Health whether to grant ITSNA's application for expansion of its scope of recognition. The Assistant Secretary will make the final decision on granting the application. In making this decision, the Assistant Secretary may undertake other proceedings prescribed in Appendix A to 29 CFR 1910.7. OSHA will publish a public notice of its final decision in the Federal Register. Authority and Signature David Michaels, Ph.D., MPH, Assistant Secretary of Labor for Occupational Safety and Health, 200 Constitution Avenue NW., Washington, DC 20210, authorized the preparation of this notice. Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 2012), and 29 CFR 1910.7. Signed at Washington, DC, on October 25, 2016. David Michaels, Assistant Secretary of Labor for Occupational Safety and Health. [FR Doc. 2016-26203 Filed 10-28-16; 8:45 am] BILLING CODE 4510-26-P
| Category | Regulatory Information | |
| Collection | Federal Register | |
| sudoc Class | AE 2.7: GS 4.107: AE 2.106: | |
| Publisher | Office of the Federal Register, National Archives and Records Administration | |
| Section | Notices | |
| Action | Notice. | |
| Dates | Submit comments, information, and documents in response to this notice, or requests for an extension of time to make a submission, on or before November 15, 2016. | |
| Contact | Information regarding this notice is available from the following sources: | |
| FR Citation | 81 FR 75442 |