83 FR 17143 - Foreign-Trade Zone (FTZ) 293-Limon, Colorado; Notification of Proposed Production Activity; Laser Galicia America LLC (Bending and Assembly of Trafo Wall); Aurora, Colorado

DEPARTMENT OF COMMERCE
Foreign-Trade Zones Board

Federal Register Volume 83, Issue 75 (April 18, 2018)

[Federal Register Volume 83, Number 75 (Wednesday, April 18, 2018)]
[Notices]
[Page 17143]
From the Federal Register Online  [www.thefederalregister.org]
[FR Doc No: 2018-08120]


-----------------------------------------------------------------------

DEPARTMENT OF COMMERCE

Foreign-Trade Zones Board

[B-24-2018]


Foreign-Trade Zone (FTZ) 293--Limon, Colorado; Notification of 
Proposed Production Activity; Laser Galicia America LLC (Bending and 
Assembly of Trafo Wall); Aurora, Colorado

    The Town of Limon, Colorado, grantee of FTZ 293, submitted a 
notification of proposed production activity to the FTZ Board on behalf 
of Laser Galicia America LLC (Laser Galicia), located in Aurora, 
Colorado. The notification conforming to the requirements of the 
regulations of the FTZ Board (15 CFR 400.22) was received on April 6, 
2018.
    The applicant indicates that it will be submitting a separate 
application for FTZ usage-driven designation at the Laser Galicia 
facility within FTZ 293. The facility is used for the bending and 
assembly of trafo wall. Pursuant to 15 CFR 400.14(b), FTZ activity 
would be limited to the specific foreign-status materials and 
components and specific finished products described in the submitted 
notification (as described below) and subsequently authorized by the 
FTZ Board.
    Production under FTZ procedures could exempt Laser Galicia from 
customs duty payments on the foreign-status components used in export 
production. On its domestic sales, for the foreign-status materials/
components noted below, Laser Galicia would be able to choose the duty 
rate during customs entry procedures that apply to front section trafo 
wall, top section trafo wall, and left section trafo wall (duty rate--
3.0%). Laser Galicia would be able to avoid duty on foreign-status 
components which become scrap/waste. Customs duties also could possibly 
be deferred or reduced on foreign-status production equipment.
    The components and materials sourced from abroad include: Small nut 
plate (galvanized steel thickness 10 mm); bracket for lubrication 
system--unfolded (stainless steel thickness 3 mm); frame assembly--
unfolded (galvanized steel thickness 2 mm); cross plate trafo wall--
unfolded (galvanized steel thickness 1.5 mm); shield for trafo 
component--unfolded (galvanized steel thickness 1.5 mm); structural 
sections of trafo wall--unfolded (galvanized steel thickness 1.5 mm); 
bracket angle front lock plate trafo--unfolded (galvanized steel 
thickness 2 mm); front section trafo wall--unfolded (galvanized steel 
thickness 1.5 mm); holder for cross plate--unfolded (galvanized steel 
thickness 1.5 mm); bracket for right trafo wall (galvanized steel 
thickness 2 mm); cover for actuator--unfolded (galvanized steel 
thickness 2 mm); cover for vibration sensor--unfolded (galvanized steel 
thickness 2 mm); outlet air guide--unfolded (aluminum thickness 3 mm); 
and, air choke plate--unfolded (aluminum thickness 3 mm) (duty rates 
range from 2.5% to 2.9%).
    Public comment is invited from interested parties. Submissions 
shall be addressed to the Board's Executive Secretary at the address 
below. The closing period for their receipt is May 29, 2018.
    A copy of the notification will be available for public inspection 
at the Office of the Executive Secretary, Foreign-Trade Zones Board, 
Room 21013, U.S. Department of Commerce, 1401 Constitution Avenue NW, 
Washington, DC 20230-0002, and in the ``Reading Room'' section of the 
Board's website, which is accessible via www.trade.gov/ftz.
    For further information, contact Juanita Chen at 
[email protected] or 202-482-1378.

    Dated: April 11, 2018.
Andrew McGilvray,
Executive Secretary.
[FR Doc. 2018-08120 Filed 4-17-18; 8:45 am]
 BILLING CODE 3510-DS-P