83 FR 61336 - Airworthiness Directives; Bombardier, Inc., Airplanes

DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration

Federal Register Volume 83, Issue 230 (November 29, 2018)

Page Range		61336-61338
FR Document		2018-25880
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This proposed AD was prompted by a report that certain split ball bearings used in main landing gear (MLG) side brace actuator assemblies are manufactured from material that does not meet the required material properties. This proposed AD would require an inspection of the left and right MLG side brace actuator assembly and, if necessary, replacement of the split ball bearing. We are proposing this AD to address the unsafe condition on these products.
Federal Register, Volume 83 Issue 230 (Thursday, November 29, 2018)
[Federal Register Volume 83, Number 230 (Thursday, November 29, 2018)]
[Proposed Rules]
[Pages 61336-61338]
From the Federal Register Online  [www.thefederalregister.org]
[FR Doc No: 2018-25880]


========================================================================
Proposed Rules
                                                Federal Register
________________________________________________________________________

This section of the FEDERAL REGISTER contains notices to the public of 
the proposed issuance of rules and regulations. The purpose of these 
notices is to give interested persons an opportunity to participate in 
the rule making prior to the adoption of the final rules.

========================================================================


Federal Register / Vol. 83, No. 230 / Thursday, November 29, 2018 / 
Proposed Rules

[[Page 61336]]



DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2018-0965; Product Identifier 2018-NM-124-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier, Inc., Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain Bombardier, Inc., Model BD-100-1A10 airplanes. This proposed AD 
was prompted by a report that certain split ball bearings used in main 
landing gear (MLG) side brace actuator assemblies are manufactured from 
material that does not meet the required material properties. This 
proposed AD would require an inspection of the left and right MLG side 
brace actuator assembly and, if necessary, replacement of the split 
ball bearing. We are proposing this AD to address the unsafe condition 
on these products.

DATES: We must receive comments on this proposed AD by January 14, 
2019.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE, Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this NPRM, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec 
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email 
[email protected]; internet http://www.bombardier.com. You 
may view this service information at the FAA, Transport Standards 
Branch, 2200 South 216th St., Des Moines, WA. For information on the 
availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0965; or in person at Docket Operations between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays. The AD docket contains 
this NPRM, the regulatory evaluation, any comments received, and other 
information. The street address for Docket Operations (phone: 800-647-
5527) is in the ADDRESSES section. Comments will be available in the AD 
docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Darren Gassetto, Aerospace Engineer, 
Mechanical Systems and Admin Services Section, FAA, New York ACO 
Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 
516-228-7323; fax 516-794-5531; email [email protected].

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2018-0965; 
Product Identifier 2018-NM-124-AD'' at the beginning of your comments. 
We specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of this NPRM. We will consider all 
comments received by the closing date and may amend this NPRM because 
of those comments.
    We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this NPRM.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation 
authority for Canada, has issued Canadian AD CF-2018-20, dated July 27, 
2018 (referred to after this as the Mandatory Continuing Airworthiness 
Information, or ``the MCAI''), to correct an unsafe condition for 
certain Bombardier, Inc., Model BD-100-1A10 airplanes. The MCAI states:

    The landing gear supplier has informed Bombardier Aerospace 
about a quality escape involving Main Landing Gear (MLG) side brace 
actuators that have been assembled using non-conforming split ball 
bearings. The affected bearings are manufactured from material that 
does not meet the required material properties. If not corrected, 
this condition can result in potentially asymmetric MLG gear 
extension or retraction and subsequent gear collapse during landing.
    This AD mandates verification of the installed MLG side brace 
actuator assemblies and replacement of the affected parts.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-
0965.

Related Service Information Under 1 CFR Part 51

    Bombardier, Inc., has issued Service Bulletin 100-32-30, dated 
December 18, 2017, and Service Bulletin 350-32-006, dated December 18, 
2017. The service information describes procedures to perform an 
inspection of the left and right MLG side brace actuator assembly to 
verify the serial number and replacement of the split ball bearing. 
These documents are distinct since they apply to airplanes in different 
configurations. This service information is reasonably available 
because the interested parties have access to it through their normal 
course of business or by the means identified in the ADDRESSES section.

FAA's Determination

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all the relevant information and determined

[[Page 61337]]

the unsafe condition described previously is likely to exist or develop 
on other products of the same type design.

Proposed Requirements of This NPRM

    This proposed AD would require accomplishing the actions specified 
in the service information described previously.

Costs of Compliance

    We estimate that this proposed AD affects 468 airplanes of U.S. 
registry. We estimate the following costs to comply with this proposed 
AD:

                                      Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
                                                                                    Cost per       Cost on U.S.
                          Labor cost                              Parts cost        product         operators
----------------------------------------------------------------------------------------------------------------
1 work-hours x $85 per hour = $85............................              $0              $85          $39,780
----------------------------------------------------------------------------------------------------------------

    We estimate the following costs to do any necessary on-condition 
actions that would be required based on the results of the required 
inspection. We have no way of determining the number of aircraft that 
might need this on-condition actions:

                 Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
                                                             Cost per
              Labor cost                   Parts cost        product
------------------------------------------------------------------------
8 work-hours x $85 per hour = $680....          $1,820           $2,500
------------------------------------------------------------------------

    According to the manufacturer, some or all of the costs of this 
proposed AD may be covered under warranty, thereby reducing the cost 
impact on affected individuals. We do not control warranty coverage for 
affected individuals. As a result, we have included all known costs in 
our cost estimate.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.
    This proposed AD is issued in accordance with authority delegated 
by the Executive Director, Aircraft Certification Service, as 
authorized by FAA Order 8000.51C. In accordance with that order, 
issuance of ADs is normally a function of the Compliance and 
Airworthiness Division, but during this transition period, the 
Executive Director has delegated the authority to issue ADs applicable 
to transport category airplanes to the Director of the System Oversight 
Division.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13   [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

Bombardier, Inc.: Docket No. FAA-2018-0965; Product Identifier 2018-
NM-124-AD.

(a) Comments Due Date

    We must receive comments by January 14, 2019.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to Bombardier, Inc., Model BD-100-1A10 
airplanes, certificated in any category, serial numbers 20003 
through 20500 and 20501 through 20665 inclusive.

(d) Subject

    Air Transport Association (ATA) of America Code 32, Landing 
gear.

(e) Reason

    This AD was prompted by a report that certain split ball 
bearings used in main landing gear (MLG) side brace actuator 
assemblies are manufactured from material that does not meet the 
required material properties. We are issuing this AD to address 
these non-conforming split ball bearings, which, if not corrected, 
can result in potentially asymmetric MLG extension or retraction and 
consequent collapse of the MLG during landing.

[[Page 61338]]

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspection

    At the applicable time specified in figure 1 to paragraphs (g) 
and (h) of this AD: Perform an inspection to verify the serial 
number of the left and right MLG side brace actuator assembly P/N 
40310-103, in accordance with paragraphs 2.A. and 2.B. of the 
Accomplishment Instructions of Bombardier Service Bulletin 100-32-
30, dated December 18, 2017; or perform an inspection to verify the 
serial number of the left and right MLG side brace actuator assembly 
P/N 2-8554-2, in accordance with paragraphs 2.A. and 2.B. of the 
Accomplishment Instructions of Bombardier Service Bulletin 350-32-
006, dated December 18, 2017; as applicable.
[GRAPHIC] [TIFF OMITTED] TP29NO18.001

(h) Replacement

    If, during the inspection specified in paragraph (g) of this AD, 
the serial number of the part installed is listed in table 1 of 
paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 100-32-30, dated December 18, 2017; or table 1 of 
paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 350-32-006, dated December 18, 2017; as applicable: 
at the applicable time specified in figure 1 to paragraphs (g) and 
(h) of this AD replace the split ball bearing P/N 104467672, in 
accordance with paragraph 2.C. of the Accomplishment Instructions of 
Bombardier Service Bulletin 100-32-30, dated December 18, 2017; or 
paragraph 2.C. of the Accomplishment Instructions of Bombardier 
Service Bulletin 350-32-006, dated December 18, 2017, as applicable. 
If the serial number of the installed part is not listed in table 1 
of paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 100-32-30, dated December 18, 2017; or table 1 of 
paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 350-32-006, dated December 18, 2017; as applicable, 
no further action is required by this paragraph.

(i) Parts Installation Limitation

    As of the effective date of this AD, no person may install on 
any Bombardier, Inc., Model BD-100-1A10 airplane, any MLG side brace 
actuator assembly on with a serial number listed in table 1 of 
paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 100-32-30, dated December 18, 2017; or table 1 of 
paragraph 2.B. of the Accomplishment Instructions of Bombardier 
Service Bulletin 350-32-006, dated December 18, 2017; as applicable, 
unless the split ball bearing P/N 104467672 has been previously 
replaced as specified in paragraph (h) of this AD.

(j) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, New 
York ACO Branch, FAA, has the authority to approve AMOCs for this 
AD, if requested using the procedures found in 14 CFR 39.19. In 
accordance with 14 CFR 39.19, send your request to your principal 
inspector or local Flight Standards District Office, as appropriate. 
If sending information directly to the manager of the certification 
office, send it to ATTN: Program Manager, Continuing Operational 
Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, 
Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before 
using any approved AMOC, notify your appropriate principal 
inspector, or lacking a principal inspector, the manager of the 
local flight standards district office/certificate holding district 
office.
    (2) Contacting the Manufacturer: For any requirement in this AD 
to obtain corrective actions from a manufacturer, the action must be 
accomplished using a method approved by the Manager, New York ACO 
Branch, FAA; or Transport Canada Civil Aviation (TCCA); or 
Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If 
approved by the DAO, the approval must include the DAO-authorized 
signature.

(k) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information 
(MCAI) Canadian AD CF-2018-20, dated July 27, 2018, for related 
information. This MCAI may be found in the AD docket on the internet 
at http://www.regulations.gov by searching for and locating Docket 
No. FAA-2018-0965.
    (2) For more information about this AD, contact Darren Gassetto, 
Aerospace Engineer, Mechanical Systems and Admin Services Section, 
FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, 
NY 11590; telephone 516-228-7323; fax 516-794-5531; email [email protected].
    (3) For service information identified in this AD, contact 
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, 
Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-
7401; email [email protected]; internet http://www.bombardier.com. You may view this service information at the 
FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, 
WA. For information on the availability of this material at the FAA, 
call 206-231-3195.


    Issued in Des Moines, Washington, on November 15, 2018.
Dionne Palermo,
Acting Director, System Oversight Division, Aircraft Certification 
Service.
[FR Doc. 2018-25880 Filed 11-28-18; 8:45 am]
 BILLING CODE 4910-13-P
Document Created: 2018-11-28 23:44:20
Document Modified: 2018-11-28 23:44:20
Category		Regulatory Information
Collection		Federal Register
sudoc Class		AE 2.7: GS 4.107: AE 2.106:
Publisher		Office of the Federal Register, National Archives and Records Administration
Section		Proposed Rules
Action		Notice of proposed rulemaking (NPRM).
Dates		We must receive comments on this proposed AD by January 14, 2019.
Contact		Darren Gassetto, Aerospace Engineer, Mechanical Systems and Admin Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7323; fax 516-794-5531; email [email protected]
FR Citation		83 FR 61336
RIN Number		2120-AA64
CFR Associated		Air Transportation; Aircraft; Aviation Safety; Incorporation by Reference and Safety
83 FR 61336 - Airworthiness Directives; Bombardier, Inc., Airplanes

DEPARTMENT OF TRANSPORTATIONFederal Aviation Administration

Federal Register Volume 83, Issue 230 (November 29, 2018)

DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
